SMART-HOUSE CONTROLLER 10-30V

Deleted completely per. May 1, 2018.

The BH8-CTRLz, popularly referred to as Generation 1 and 2, has for many years been the backbone of the Smartbuilding system until 4 years ago was replaced by our latest and the current check: SH2/SB2.

Upgrade to the UWP Platform SH2WEB24 See more HERE

DESCRIPTION

Intelligent functions programmable be the controller is equipped with a dedicated intelligent functions for lighting control, awnings / blinds, temperature and alarm systems, and it is therefore especially suitable for building automation. It can also be configured to perform the time, timer and logic functions.

In the Windows-based configuration software is there for-programmed features makes the programming very easy. The configuration of the smart-house controller smart-house controller is as default set to function as a channel-controller without intelligent features. In order to be able to make use of the intelligent features, the smart-house controller is programmed using the user-friendly windowsbasere - the configuration software that is included in the package and which can be installed on pcs with Win 95/98/2000/NT/XP.

When the programming is complete, transfer the configuration to the smart-house controller via COM1 (RS232 port). The configuration can be saved as a file, and it can also be transmitted from a be controller. GSM modem BH8-CTRLZG-xxx the smart-house controller has built-in GSMmodem which enables the monitoring and control of smart-housesignaler via SMS-messages to and from GSM mobile phone. You can use the SMS messages in three different ways: • the smart-house controller can be programmed to send out event based SMS messages.

An incident can be a kanalomskiftning to ON or OFF, or it can be an analog signal crossing a setpoint. • The Status of digital or analog data can be read and answered via SMS. • Status of digital channels can be controlled with commands via SMS. The following is required, if GSMmodemet must be activated: • There must be inserted a sim-card with pin-code 9090 in the castle on the front of the BH8-CTRLZG-xxx.

The Sim card must be of type 3 volt. • A GSM antenna must be connected to the FME connector on the BH8-CTRLZGxxx. If the device is installed in a metal enclosure, the antenna must be installed outside the cabinet and connected to smart-house controller with a cable. (This type of antenna can be obtained as accessories). GSM-modem current status is displayed on the front of the BH8-CTRLZG-xxx by means of a light-emitting diode. Through various blinkesignaler indicates the led "connect", "sim card is missing", "network not found", "modem not responding", "SMS sent" and "SMS received". Radio controlled clock

It is possible to equip the BH8 - CTRLZG-xxx with an external antenna to a radio controlled clock to achieve high precision in connection with the tidsindstillingsfunktioner and the time of the events. When using the ANT2 antenna will BH8-CTRLZG-xxx to receive accurate time signals from the DCF77 transmitter in Frankfurt. The antenna transmits the demodulated signals to the smart-house controller via an open collector driver. DCF77 transmitter covers all of Central europe, with its senderadius is at least 1000 km. At larger distances depends on ANT2 - antenna applicability of modtagerforholdene. ANT2-tied to the BH8-CTRLZG-xxx-terminals. The RS232 ports on the Smart-house controller is equipped with two RS232 ports (COM1 and COM2) which both can be used by a PC or PLC for reading and writing Duplinadata by means of the Modbus-RTUprotokollen. COM1 is also used for download and upload of configuration files (which is created in the smart-house controller configuration software) and for firmware upgrade.

If you want external radio modem, it must be connected to COM2. COM1 has a fixed baudrate of 115 kBaud, while the COM2's baud rate is adjustable. RS485 port RS484 port provides the ability to netværkstilslutte up to 32 smart-house controllers as Modbus-RTU slaves. On the way, can the PC or PLC, which acts as a RS484 Modbus-RTUmaster, to communicate data to and from any of the 32 smart-house controllers. Each device must be assigned an address by using existing configuration software.

Can be with RS484 network create up to 4096 of the smart-house-In/Opunkter from a PC or PLC. See the following RS484-network diagram. Modbus-RTU protocol using the Modbus-RTU commands 2 and 3 through COM1 and COM2, you can read all kind of smart-house data (digital, analinke, multiplexed analog or counter data). You can control the status of digital and multiplexed analog data and reset of the counter via the commands 5, 6 and 16. See manual for memory mapinformation.

On-board I/O the Smart-house controller has 4 digital inputs and 4 digital outputs on-board. They are implemented in order to reduce the cost of fjernstationer to a few signals (f.ex. in connection with an SMS alarm system or radio modem-fjernstationer). On-board I/O's used by means of the logical features of the smart-house controller, where they can be assigned to specific kanaladresser.

• Weight 640g
• Protection IP20
• Beskyttelsesgrad 3 (IEC 60664)
• Operating temperature 0° til +50°C
• Storage temperature -20 - +85 °C
• Humidity (non-condensing) 20 til 80% RH
• House Dimensions H8-hus
• Mounting DIN-skinne
• Power supply 24 VDC +/-20%

• Manual
  
  
• Manual BH8-CTRLZ