PIR Sensor for Ceiling

• Passive infrared detector (PIR)
• Detects movement and presence
• Indoor applications
• Smart-house output
• Operating distance: max. 8 m
• Operating angle: 90°
• LED indication
• Supplied by bus
• Mounting in LK ceilingbox PL52 or PL55

Product Description

The BSB-PIR90-U is a 90° PIR sensor to detect presence and/or movement in indoor installations. It is part of the smart-house concept and can be used to control lights, rollerblinds, air-conditioning, intruder alarms and all the other functions supported by the smart-house system, in an automatic way depending on people-presence. This sensor is completely programmable via the SH tool.

Mode of Operation

This PIR sensor responds to any fluctuation in infrared heat radiation, so any object or human presence changes the thermal image detected by the sensor when entering its field of vision. The sensor is equipped with a segmented lens that divides the field of vision into active and passive zones (zones not visible to the sensor, see figures “Horizontal and Vertical sensitive area”). When a heat source crosses these zones, the sensor detects the change in infrared radiation and presence and/or movement are recognised. How sensitive and fast the sensor has to be to detect presence and/or movement can be programmed by means of four parameters, by means of the SH tool if the sensor is controlled by a master unit SH2WEB24 or by using the programmer BGP-COD-BAT if the sensor is connected to a BH8-CTRLX- 230. The four parameters are: mode of detecting the crossing of active zones, sensitivity, the number of pulses and the time window in which these pulses have to be detected. These four parameters have to be set for both presence and movement recognition. Movement is used by the system in the intruder alarm function and to switch the light on, while presence is used in the light function to reload the energy-save timer (i.e. each time presence is detected, the energy-save timer starts counting from the beginning).

Mounting

the PIR detector is designed for ceiling mounting. As the BSB-PIR90-U is a passive device, several detectors can be placed in the same room without interfering with each other. The module should not be installed as follows: a) Outdoors. b) In places exposed either to sunlight or to motor vehicle headlights pointing directly at the sensor. c) In places exposed to direct air flow from a heater or air conditioner. d) In places where rapid temperature changes occur. e) In places exposed to severe vibration. f) Close to glass or other objects which might reflect the infrared radiation. Note: If the sensor is to detect presence, please be careful to mount it so that the area where presence has to be detected is completely covered by the sensitive area of the sensor. See figures “Horizontal and Vertical sensitive area”

• For Controller UWP 3.0 - SH2WEB24 - SB2WEB24 - SA2WEB24
• Also compatible with ..: BH8-CTRLZ - BH8-CTRLX - G3800xx01x - or Dupline-Generator SH2DUG24
• Address assignment Auto through "SIN" (Specific Identification Number) or via BGP-COD-BAT
• Adressedeling. If it used with the BH8-CTRLX-230, the channels have to be programmed by the BGP-COD-BAT
• Weight 25g
• Protection IP20
• Forside IP50
• Screw terminal IP 20
• Beskyttelsesgrad 3 (IEC 60664)
• Operating temperature 0° til +50°C
• Storage temperature -20° til +70°C
• Humidity (non-condensing) 20 til 80% RH
• House Dimensions LK PL-box Mechanics
• DIM.: Ø 76 x 25 mm
• Color white
• Power supply Supplied by Dupline®bussen
• Other compatible components LK PL-dåse

• BSB-PIR90-U_swe.pdf
  
  
• BSB-PIR90-U_esp.pdf
  
  
• BSB-PIR90-U_sve.pdf
  
  
• BSB-PIR90-U_nor.pdf
  
  
• BSB-PIR90-U_fra.pdf
  
  
• BSB-PIR90-U_deu.pdf
  
  
• BSB-PIR90-U_eng.pdf
  
  
• BSB-PIR90-U_ita.pdf
  
  
• BSB-PIR90-U_spa.pdf
  
  
• BSB-PIR90-U.JPG
  
  
• BSB-PIR90-U_dan.pdf