Search on blog

Smart House UWP

Home

Home

Home

Home

Wireless base modules m. External antenna

1

Wireless base modules m. External antenna

By buying this product you can collect up to 13 loyalty points. Your cart will total 13 points that can be converted into a voucher of 6,50 kr.


BH4-WBU-230
Smart-house transceiver for building automation applications
Easy to install in both new and older installations
No limit on number of connected switches BH4-WBU-230
DIN rail mounting
Range up to 100 meters in open air
Easy to operate
external antenna

 

More details

BH4-WBUA-230

1 362,50 kr

  • BH4-WBU-230

    MODE OF OPERATION


    The wireless switches BFX-WLS4 programmed as standard
    VGA / Opus switches (but without channel coding for (I / O 5-8), since the LEDs
    automatically follows press buttons). The communication between the
    wireless switch Bxx-WLS4 and base station BH4-WBU-230
    created as follows:
    The used smart house addresses on the wireless devices are programmed
    all of the wireless device. The only special interaction related
    wireless devices is the association process (the Association).
    This process ensures that wireless devices is not disturbed by
    other wireless devices.
    To associate a device to the base:
    1) Press the Mode button on the base. Associate LED lights.
    2) Press a button on the wireless device to be attached. - All
    LEDs on the device will light for about 1 second.
    3) Press the mode button on the base until both ASSOCIATE- and
    Disable LEDs off. This indicates normal operation.
    If the connection from a wireless device fails, all LEDs
    flash briefly when communication is attempted established with base unit
    three times.
    If a device is associated with base station A, base, and both A and B are in the
    its scope, the following procedure is used if
    you want to reassociate the device at the base B:
    1) Select Disable mode on base A.
    2) Select Associatemode on base B.
    3) Press a button on the wireless device to be attached - All
    LEDs on the device will light for about 1 second.
    4) Press the mode button on both bases until both
    ASSOCIATE- and Disable-LED goes out. this indicates
    normal function.
    LEDs:
    Power LED indicates that the unit is powered (230 VAC).
    Smart-house OK LED indicates that detected a smart house signal. RF LED indicates received wireless communication with the base.
    Associate-LED indicates connection (Association). Disable LED indicates that the base ignores any wireless communications.

     

    • For Controller BH8-CTRLX - BH8-CTRLZ - G3800xx01x
    • Also compatible with ..: Can be used on a Sx2WEB24 Check with a SH2DUG24 Dupline-Generator
    • Address assignment BGP-COD-BAT
    • Adressedeling. If used the same with SH2DUG24 - Read the Dupline HW manual for Compatibility mode
    • Weight 250g
    • Protection IP20
    • Beskyttelsesgrad 3 (IEC 60664)
    • Operating temperature -20°C til +50°C (-4° til + 122°F)
    • Storage temperature -50°C til +85°C (-58° til +185°F)
    • Humidity (non-condensing) 20 til 80% RH
    • House Dimensions 2-DIN-modul
    • Datasheet / Manual Download Data Sheet / Manual - click on the tab Download
    • Mounting DIN-skinne
    • DIM.: 72 x 77 x70 mm
    • Power supply 230 VAC, ±15%

    Reviews

    Write a review

    Wireless base modules m. External antenna

    Wireless base modules m. External antenna

    BH4-WBU-230
    Smart-house transceiver for building automation applications
    Easy to install in both new and older installations
    No limit on number of connected switches BH4-WBU-230
    DIN rail mounting
    Range up to 100 meters in open air
    Easy to operate
    external antenna

     

    Write a review

    3 other products in the same category: